- HIGH EFFICIENT FILTRATION-3-Stage Reverse Osmosis Drinking Water Filtration System with NSF certificated Thin-film composite RO membrane filters down to 0.0001 micron,Reduce 99% contaminant ,including Heavy Metal, Arsenic, Lead ,Mercury ,Fluoride,Hardness,Cadmium,Chlorine,Taste,Odor,Asbestos, Lead,and more 1000+ contaminants.
- HIGH QUALITY-- all tube, fittings,Ro membrane complies with NSF/ANSI standard 58 to provide healthy, safe, and pure water.
- EASY&CONVENIENT-Streamlined DIY filter installation; fits most under sink cabinets, the ratio of pure water and waste water is 1:2.
- Tankless and without faucet,but add-On Drinking Water Kit with 2.8 Gallon Tank available, Amazon asin :B07D9JKSLJ or B07DBZN79S.
- ISO9001:2008 certificated Manufacturer ,also Member of Water Quality Association (WQA).
FEED WATER PRESSURE:40 - 100 PSI
MAX. TDS :1000 PPM
TURBIDITY < 1.0 NTU
MAX SDI <4.0
HARDNESS < 5 GPG
Shelf life: 3Years
Warranty: 1year limited warranty .
More valuable information:
✪What is dimension of installed Geekpure 3-Stage Aquarium Ro system?
RO unit: Length 14.80 inch, Width 9.2 inch, Height 3.2 inch.
Product weight:4 lb
✪What is 3 stage filter and function?
The 1st stage: PP spun filter, Remove sand, dirt, sediment.
The 2nd stage: Carbon filter, Remove chlorine, taste & odors, very fine particulates
The 3rd stage: TFC Ro membrane, Reduce 99% total dissolved minerals, heavy metal, Arsenic, Mercury, Iron, lead ,Fluoride and 1000+ contaminants .
✪Where can i buy replace filters?
Please search product ASIN B07KHWKVCS on Amazon.
There is not storage tank and faucet in the box.Because it is special design for aquarium use.
If you need these,please search product ASIN B07DBZN79S,B07D9JKSLJ,B078HTMHXV on Amazon and buy it separately.
✪What is in the box?
1SET filters (3 pieces filters),diverter valve,1 piece wrench,some fittings,water pipe,clips,drain clamp,and so on.
Yes, BPA free .
1.It Is Recommended to Wait Until the Entire System Is Pressurized and Re-Check for Any Leaks Before Leaving Installation Site.
2.Please keep flush filters 30 minutes before it is used to feed for your aquarium .
It Is Normal for Some Black Carbon Fines to Appear When You Flush Carbon Filter.
3.Push the Tubing All the Way in and Use Teflon Tape During Installation.
If you��re looking for a good RO system at a great price, this is a great choice. I was concerned that I might ��get what I pay for�� with this system, but I��ve been pleasantly surprised!My only issue with the system is that the valve they supply is total crap and had a slight leak and felt like it was going to break every time I turned it. I replaced it with a one piece casted valve instead of the 2-part valve they provided.Other than that, I��ve tested the water and it has 0 TDS after passing through the system.
Works great.. very easy to install. I plumbed straight to a hose bib in laundry room waste water goes down washing machine drain. Seems to be better for plants than water machines in front of grocery stores. Highly recommended for smaller hobby grow. Comes out at 0 ppm.
I'm not using this for the sink or an aquarium. I need a cheap supply of 0 TDS water for Nepenthes and Sarracenia. Using a ZeroWater TDS meter I see this outputs the desired 0 TDS water quality.The hardware store had the parts for me to hook this up either to my kitchen sink or a garden hose. The metal hose in my photo came from the hardware store. The filter includes all of the plastic parts and the valved metal connector. White is the input, blue is the pure output, red is the reject output.The reverse osmosis water output feels slow, but it's faster than a ZeroWater pitcher. It outputs both usable and reject water at a ratio of 1 to 2, so there's a lot of reject water for watering the less sensitive plants.The manual says the reverse osmosis filter should last at least a full year and perhaps two, while the sediment and carbon filters last six to twelve months.As the key piece in my experimental DIY project, this filter has been perfect.
Works as advertised
Bought this unit to use for my aquariums (South American fish). After the initial system flush I tested the water (day 1) pH in the low 6's GH & KH in the 0 - 2 range. Plan is to slowly introduce small amounts of R/O water during water changes and slowly get my water to a lower pH and softer. ...so...so far so good. btw - I didn't want a permanent undersink setup so I bought the faucet adapter and just hooked it up to my kitchen faucet...easy to do and remove.